Date of this Version
EXPLANATION OF TEST REPORT: John Deere A
TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.
This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.
BELT HORSEPOWER TESTS
TEST B: The throttle valve is hdd wide opened and the belt load on the dynamometer is adjusted so that the engine is at the rated speed recommended by the manufacturer. Carburetor, ignition timing and manifold adjustments are all set for maximum engine power.
This test is designed to determine maximum belt horsepower of the tractor at ra.te.d speed and to measure fuel consumption at the maximum power on the belt.
TEST C: For tractors with carburetors the best fuel economy does not always occur when the engine develops maximum power at rated speed. Test C is intended to allow the manufacturer's representative to select a more economical fuel setting even though there is a slight loss of power. This more practical carburetor setting is used in all later tests except test F. The throttle valve is held wide open and load adjusted to give rated rpm. Tests Band C are the same for diesel tractors, which have an altogether different fuel system.
TEST D: The throttle control lever is set so that the governor will maintain rated engine speed when rated load is applied. Rated load is 85% of 100% maximum, as obtained in test B, corrected to standard conditions. This rating is somewhat less than the maximum belt horsepower in order that the operator may have a certain amount of reserve.
TEST E: Varying load serves to show the range of engine speeds when the engine is controlled by the governor during the following varied loads of 20 minutes each: rated load, no load, 1/2 rated load, maximum load at wide open throttle valve, 1/4 and 3/4 rated load.
The average result of this test shows the average power and fuel consumption. Since the average tractor is subjected to varying loads, these data serve well in predicting fuel consumptionand efficiency of a tractor in general use.
Torque, lb-ft at dynamometer, is obtained with wide open throttle and sufficient load is applied to give several readings.
DRAWBAR HORSEPOWER TESTS
In all drawbar tests the pull exerted by the tractor is transmitted by a hydraulic pressure cylinder to a recording instrument in the test car. All tests are made on the same dirt test course which is maintained by grading, sprinkling and rolling so that it remains very nearly the same throughout the season. The same tires, wheels and weights are used for all tests except J and K.
TEST F: A drawbar test, the results of which are used to determine the rated drawbar horsepower in test H. The carburetor is set to develop maximum power as in test B. The rated gear recommended by manufacturer as plow gear is used in this test. The drawbar load is adjusted to give rated engine speed.
TEST G: Maximum drawbar horsepower is determined in each gear when the carburetor is set for fuel economy as in test C. The throttle valve is held wide open and the load is applied so that the engine runs at rated engine speed. When operating in low gear it is not uncommon for the tractor to develop less drawbar horsepower than in rated gear because of excessive wheel slippage. When excessive wheel slippage occurs the load is reduced until slippage approaches 16%. When the load is reduced it is necessary to operate the tractor engine at part throttle and control engine speed by governor action.
TEST H: Intended to test the ability of the tractor to run continuously for 10 hours at rated drawbar horsepower and to determine the fuel consumption during that time. Rated drawbar horsepower is 75% of 10°% maximum drawbar horsepower (Test F), corrected to standard conditions.
When operating at rated load the throttle control lever is set to maintain rated engine speed. This rating is less than maximum drawbar horsepower in order that the operator may have a certain amount of reserve.
TEST J: The tractor is operated in rated gear with all added weight removed. This test shows the effect of the removal of added weight on the performance of the tractor when compared with test G. Removal of wheel weights generally increases wheel slippage and decreases drawbar horsepower.
TEST K: Similar to test J except that the smallest tires and lightest wheels offered by the manufacturer are used.